How To Use A Head Gasket Sealer

As a car owner, it’s great to look for some simple DIY repairs because you can’t take it to a mechanic all the time. It’s a good idea to use head gasket sealer for repairing any head gasket leaks. By this way, you can save your money. You may have to face many problems caused by a leaking head gasket. So, it’s important to know how to repair properly. Head gasket sealers promise to give a temporal or permanent seal. So, there will be no leaks in the head gasket. Sure, you wonder how you can use a head gasket sealer, right? Let’s check out this post for the question.

What is a Head Gasket Sealer

It’s actually an important part of any car with the engine block and cylinder head separated. It can be able to give the greatest degree of compression. Also, it can help to reduce the leakage of oil or coolant. When owning a blown head gasket, it may be a disadvantage for you. Also, it’s called a gasket sealant. There are many different forms of the head gasket sealer such as glue, spray, or paste. Thanks to it, your car can also reduce the number of fluid leakages you experience. Most importantly, you need to choose the best quality.

How to Prevent Blowing A Head Gasket

Just by giving your head gasket a little bit of maintenance, your driving can last long. So, you can save a small fortune. It’s essential to change the fluids every 3000 miles. The temperature can increase significantly due to sudden and fast acceleration. As the result, your head gasket may get warping or cracking. That’s why you should accelerate slowly.

Identify Head Gasket Leak

If you want to start any repairs, you need to identify the leaks in the head gasket. Just by this way, you can seal them permanently. So, how to identify a blown head gasket? There are many signs for you such as radiator problems, engine problems, tinted spark plugs, faulty exhaust, oil leaks, and contaminated oil. Then, it’s time to gather the essential items that need to be fixed. You need a head gasket sealer, a coolant, and gloves.

Read The Instructions On The Sealer

You can start repairing without reading the instructions. Most importantly, you need to follow the guidelines on the bottle. You can determine the amount of sealer by looking at the instructions on the back of the bottle.

Drain The Old Coolant

Next, you need to drain the old coolant. Then, put the container under the radiator. You need a large basket that can hold the coolant at once. And, remove all the coolant completely. Last, you need to close the petcock. At the same time, use water to fill the radiator.

Disconnect The Thermostat

The thermostat has the purpose of maintaining the temperature. In order to prevent engaging when adding the head gasket sealer, disconnect the thermostat. You may need a help on your vehicle manual. Next, it’s time to help on your vehicle manual after adding the water. Your car needs to run for about 10 minutes. If your car becomes hotter, you need to check the temperature gauge. If necessary, turn it off.

Fill The Coolant System With The Sealer

After draining all the water completely, you need to close the petcock system. At the same time, remember to reconnect the thermostat. Next, use the coolant system and coolant mix in order to fill the coolant system. The needed ratio is 50/50. Stop adding the coolant to the radiator cap only when it is up to the required coolant capacity. It’s important to follow the instructions of the sealer.

Drive The Vehicle

It’s essential to let your car run for about 15 minutes. It can help to make the coolant system reach the head gasket. Also, this offers the sealer the opportunity to travel throughout the system. Be careful! Remember to close the engine if your vehicle becomes overheating.

Check The Status Of Your Vehicle

If you want to check whether your car has any head gasket leaks in it, you can use the same ways as to determine the leaks. It’s best to look for the best head gasket sealer. It can help to prevent any leaks from taking place. The heat from the engine is great for the process hence hardening the seal. If you still can’t deal with leaks even after using a sealer, it’s time to replace the head gasket.

Final Words

If you choose the mechanic for head gasket repairs, you may have to pay a lot of money. So, we recommend you to handle leaks on the head gasket yourself. It’s best to buy the best head gasket sealer. This can help you keep your vehicle in a good condition.


Speak Your Mind